PWM开关变换器统一建模法与谐波分析法的应用

介绍了PWM开关功率变换器电路的统一建模方法，并将谐波分析方法应用于电路分析中，理论和实例表明，这种方法容易得到电路变量的基波解和各次谐波解，以及电路的传递函数，具有容易理解和准确度较高的优点。     

Measurement of the thermal diffusivity of thin films on substrate by the photoacoustic method

Measurements of the thermal diffusivity of thin films on substrate have been performed by the photoacoustic method. In order to examine the method we have built a new apparatus and proposed (1) a system calibration procedure using optically and thermally thick reference samples and (2) a data analysis procedure based on the RG (Rosencwaig and Gersho) theory. As a result of using a transparent photoacoustic cell, the systematic errors which are caused by stray light have been reduced. With this apparatus, measurements have been performed on platinum, titanium, and stainless steel (SUS304) thin foils (thickness form 50 to 100 µm) with three different liquid backing materials (water, glycerol, and ethyl alcohol). The reproducibility was within ±7% regardless of film thickness and substrate materials.     

纳米氧化铟粉体的形貌与结构研究

用湿化学法制备了纳米极氧化铟超细粉体。利用透射电子显微镜、图像分析仪研究了纳米氧化铟粉体的形貌、尺寸分布和结构特征。结果表明，氧化铟粉体呈方片状，尺寸在10-30nm，化学组分高纯，达到了纳米级粉末要求；粉体的尺寸均匀，但在不同条件下制得的粉体，其尺寸相差较大；制备得到的氧化铟超细粉体的结构为体心立方。     

直读光度法测定钼铁中的硅

试样经草酸、双氧水分解后，以盐酸羟胺破坏掉多余双氧水。以标准样品作参比，在硫酸－柠檬酸介质中，用钼酸铵显色，抗坏血酸还原，生成稳定的硅钼蓝。此方法可测定１．０％以下的硅，具有快速、准确、灵敏度高等优点。     

延长Pd/C催化剂使用寿命的途径

影响钯 炭催化剂使用寿命的因素主要有催化剂失活 ,运输、装填过程中的磨损 ,工艺操作条件等。延长催化剂的使用寿命的途径有正确的运输、装填方法 ,定期冲洗 ,定期碱洗和分阶段调整氢气加入量     

高效液相色谱法测定头孢拉定制剂方法的改进

目的:改进头孢拉定制剂含量测定方法。方法:高效液相色谱条件:以Shim—Pack CLC—ODS(250mm×4.6mm)为色谱柱;柱温为35℃;流动相为水—甲醇—3.86％醋酸钠溶液-4％醋酸溶液(1364:500:30:6);流速为0.8mL·min~(-1);检测波长为254nm。结果:头孢拉定峰形良好,分离度和柱效满足药典要求,保留时间由原来的21.32min缩短至8.06min,提高了分析速度,含量测定结果与中国药典无显著差异。结论:该方法快速、准确、能更好地适用于常规检验工作和大批量生产时的质量控制。     

粉喷桩及其应用

简介了目前采用的粉喷桩的基本工作过程。叙述了水泥粉喷桩的加固机理：①水泥的水解和化学反应；②离子交换和团粒化作用；③水泥的凝结与硬化；④碳酸化反应。介绍了粉喷桩的应用范围，并结合工作概况、场地概述、地基加固方案选择、粉喷极的设计和质量检查等具体过程给出粉喷桩的具体应用实例。     

最优化分析使网络电路输出功率最大

用最速上升法分析具有多负载的有源线性网络电路,使其输出功率最大,它可以为电子器件端口的合理布置提供最优数据。     

Modified oil agglomeration process for coal beneficiation. III. Grinding and agglomeration using different szego mill designs

The simultaneous grinding/agglormeration process has been used to beneficiate Minto coal. Experiments with the Szego Mill, a planetary ring-roller mill with grooved rollers, have given good results. Different roller ridge/groove sizes have been tested and favourable oil-coal-water ratios established. Ash removal is closely related to grinding performance. Very short mill residence times, of the order of 10 seconds, are sufficient for microagglomerate formation. Considerable equipment and operating cost savings are possible with the modified process.     

Preparation of core–shell type nanoparticles of diblock copolymers of poly(L‐lactide)/poly(ethylene glycol) and their characterization in vitro

Core–shell type nanoparticles of poly(L ‐lactide)/poly(ethylene glycol) (LE) diblock copolymer were prepared by a dialysis technique. Their size was confirmed as 40–70 nm using photon correlation spectroscopy. The ¹H‐NMR analysis confirmed the formation of core–shell type nanoparticles and drug loading. The particle size, drug loading, and drug release rate of the LE nanoparticles were slightly changed by the initial solvents that were used. The drug release behavior of LE core–shell type nanoparticles showed an initial burst during the first 12 h and then a sustained release until 100 h. The degradation behavior of LE block copolymer nanoparticles was divided into three phases: the initial rapid degradation phase, the stationary phase, and the rapid degradation phase until complete degradation. It was suggested that lidocaine release kinetics were predominantly governed by the diffusion mechanism in the initial burst phase and after that by both of the diffusion and degradation mechanisms. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2625–2634, 2002